Tips for Controlling Oxidation and Pitting on a Wire EDM

Published 10/8/2010

Tips for Controlling Oxidation and Pitting on a Wire EDM

Additives, machine settings, workpiece materials and current technology are factors in avoiding common problems with unwanted rust and surface defects.

Tony Salvado, Regional Applications Manager, GF AgieCharmilles

Additives:

Additives do help in controlling oxidation and pitting of a variety of materials. These products help a great deal when cutting a workpiece with pre-polished surfaces.

There are a few rust-inhibitor products available on the market, but caution is advised because machine deionization bottles can remove some of these products. Rust inhibitors also require constant monitoring using a refractometer. It is critical that the correct concentration be present. It is recommend that shops get references of the product before installing it.Hirschmann Engineering USA makes a product call H2O Plus and can supply user references and application suggestions.

Settings:

When using an EDM with an anti-electrolysis generator, there are no special settings required to prevent oxidation and pitting. A shop basically uses the available technology and certain techniques to reduce oxidation.

These techniques are:

Set the water conductivity to 5 microS or less, which is typically recommended for carbide, PCD, titanium, and fine finishes (<10 micro inches). This will also help keep bluing to a minimum on older non-anti-electrolysis generators.

Check water pH. Acidic detergents used to clean parts and tank will have a dramatic effect on parts rusting and will reduce the life of the deionization bottles.

De-magnetizing parts is highly recommended. This includes carbide. If the application involves cutting parts in the gap, demagnetizing the blocks will aid in evacuating sludge produced in the kerf. This applies when the slug is the part being produced. To skim the part, it must be held using a tab and skimmed before cutting off.

Always keep the workpiece submerged. Workpiece exposure to air increases the rate of oxidation.

Use rust inhibitors.

Conduct frequent machine maintenance. Neglecting components such as power contacts and cabling will not create oxidation problems, but it will produce poor machining conditions and finishes.

Keep parts clean. If a workpiece is making poor contact on the clamping surface, arcing can occur between the two surfaces and produce a poor finish, which resembles pitting. Parts should always be clean and oxidation-free for any type of EDMing.

Use recommended micron level filters. Poor quality filters can create many issues when it comes to surface finishes. Water that is not filtered properly will diminish part surface integrity when skimming in the gap.

Mix Workpiece Materials

With all the new and old types of alloys available, material incompatibility may cause surface issues. However, EDM field technicians have yet to document an instance where this situation has occurred.

New Machines

Most current wire EDMs are equipped with Anti-Electrolysis generators, some better then others. It basically comes down to how good the technology is and how fine of a surface finish the generator is capable of producing. A machine that is capable of producing a super fine finish (< 5 micro inches) can generate optimum surface integrity.

One example is the GF AgieCharmilles CUT 1000 that can machine parts with zero corrosion. The CUT 1000 is available in an oil version. With this feature, there is absolutely no electrolysis, corrosion and virtually zero recast.

Related Content

Basics 28 Jul 2023

Rethink Quality Control to Increase Productivity, Decrease Scrap

Verifying parts is essential to documenting quality, and there are a few best practices that can make the quality control process more efficient.

Basics 24 May 2023

Custom Workholding Principles to Live By

Workholding solutions can take on infinite forms and all would be correct to some degree. Follow these tips to help optimize custom workholding solutions.

CNC Tech Talks 23 Feb 2024

6 Variations That Kill Productivity

The act of qualifying CNC programs is largely related to eliminating variations, which can be a daunting task when you consider how many things can change from one time a job is run to the next.

CNC & Machine Controls 21 Oct 2024

2 Secondary Coordinate Systems You Should Know

Coordinate systems tell a CNC machine where to position the cutting tool during the program’s execution for any purpose that requires the cutting tool to move.

Basics

Machine Shop MBA

Making Chips and Modern Machine Shop are teaming up for a new podcast series called Machine Shop MBA—designed to help manufacturers measure their success against the industry’s best. Through the lens of the Top Shops benchmarking program, the series explores the KPIs that set high-performing shops apart, from machine utilization and first-pass yield to employee engagement and revenue per employee.

Automation

AMRs Are Moving Into Manufacturing: 4 Considerations for Implementation

AMRs can provide a flexible, easy-to-use automation platform so long as manufacturers choose a suitable task and prepare their facilities.

91��Ƶ

Tips for Controlling Oxidation and Pitting on a Wire EDM